Jump to content

Mstar USB Debug Tool установка драйвера mstar


Recommended Posts

This is the hidden content, please
This is the hidden content, please

Установка драйвера mstar


При подключении к USB автоматически определяется
Mstar USB Debug Tool, запускается мастер обновления оборудования
выбрать - автоматическая установка в мастере обновления оборудования.
Найдется USB Serial Converter A. Потом заново запустится мастер обновления оборудования,
и после автоматической установки
- установится
USB Serial Converter B.
Драйвер родной FTDI 2xx т. е.
микросхема FT2232 определяется.
Думаю дальше дело техники.

MTC SOFTWARE UPDATE TOOL USING GUIDE
For MSTAR solution only
1,Connect the debug board to PC by using the USB babel.
2,The the PC will find a new hardware
.(The OS must be Windows XP).
Sequence is below:
1)

This is the hidden content, please

2)
This is the hidden content, please

3)
This is the hidden content, please

4)
This is the hidden content, please

5)
This is the hidden content, please

6)
This is the hidden content, please

7)
This is the hidden content, please

8)
This is the hidden content, please

Note:
For some reason,after the first time setup,it will find new hardware again.
You should excute this sequence three times totlal.

3.Connect the debug board to the VGA socket of the TV.
1)Enter the directory:
usb-update-toolsmstar-toolsISP_Tool V4.1.6
and double click ISP_Tool V4.1.6.exe,a window will appear.

9)
This is the hidden content, please

2)Click Read.
Select the update file which end with “.bin”.
10)
This is the hidden content, please

3)Click Config

If the board connect is ok,the “Use USB” will be selected automatically.

Otherwise,you need check the connect.

11)

This is the hidden content, please

4)Click Connect

It will show the flash name on the TV board.

This is the hidden content, please

5) Click “OK”,then click Device

Please set the items as below firstly.

12)

This is the hidden content, please

Then click New Setting Below.

6)Click Auto

This is the hidden content, please

7)Click

Run

 

This is the hidden content, please

 

After complete,it will show Blank OK,Program OK,Verify OK.

This is the hidden content, please

8) Excute “FACTORY DEFAULT

” in the MENU

 

Turn off and on the TV set.

 

This is very important.

Till now,complete successfully.

During the updating,you can hear the noise from the speakers.

If you update next unit,press Run only.

If verify error,please run again.

 

8) Excute "ЗАВОДСКОЕ УМОЛЧАНИЕ" в МЕНЮ Выключает и на ТВ установленное.
Очень важно.
До теперь, завершитесь успешно.
В течение обновления, Вы можете получить известие шум от докладчиков.
Если Вы корректируете следующее устройство, нажмите Работать только.
Если проверять ошибку, пожалуйста работайте снова.

Каждый участник форума должен проявлять активность, в решении вопросов ремонта и поиска нужной радиотехнической информации.

Вы тоже можете пополнить нашу базу ценной технической информацией, личный опыт ремонта, лично снятые прошивки, всё что вам помогает в вашей работе.

Делитесь своим опытом ремонта, помогайте другим участникам  форума в поиске информации.

Делитесь прошивками, новыми схемами, все что вы сами любите на форуме читать и смотреть!

В этом и заключается суть работы на форуме - обмен информацией!

 

Link to comment
  • 3 weeks later...

This is the hidden content, please

How to Upgrade Software of MSD209 Solution
Tips: this software tool is used to upgrade the relevant model of MSD209 solution, so it is unnecessary to install.
Open this software and then you may operate as follows:
Operation steps:
1. First install USB driver, please run the CMD_Setup.exe, connect the upgrade tool:
the USB line connect the PC parallel port,the VGA line connect the TV unit VGA port.
This is the hidden content, please

2. After opening Mstar ISP Utility V4.4.7.3 software, the following interface appears:
Seen from this picture.
This is the hidden content, please

3. If it is the first time for you to use this software tool, please click the “Config” button, confirm whether the default configuration is correct. If not,
please setup this configuration parameter as below, and click the “Connect” button, if do not detect the FLASH,
please adjust the “Speed” to slow, and connect again.
This is the hidden content, please

4. After selecting the device, click “Read” button to read the files that need to upgrade, and press “Connect”,
it will detect device type, if can not detect device, please this tool and TV connect again.
This is the hidden content, please

5. After reading files, click “Auto” button and confirm the parameter is correct, if Ok,
please click “Run” button to upgrade the software, If the software update is not Ok, please click the “Run” button and upgrade the software again.
This is the hidden content, please


How to upgrade via USB
1. copy upgrade file to USB disk, change file name to ap.bin;
2. connect USB to the TV and change to analog TV source;
3. when the TV automatic detect upgrade file, please select OK to upgrade.

Каждый участник форума должен проявлять активность, в решении вопросов ремонта и поиска нужной радиотехнической информации.

Вы тоже можете пополнить нашу базу ценной технической информацией, личный опыт ремонта, лично снятые прошивки, всё что вам помогает в вашей работе.

Делитесь своим опытом ремонта, помогайте другим участникам  форума в поиске информации.

Делитесь прошивками, новыми схемами, все что вы сами любите на форуме читать и смотреть!

В этом и заключается суть работы на форуме - обмен информацией!

 

Link to comment
Guest
This topic is now closed to further replies.
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...